Difference between revisions of "Schematics"
| (4 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
== Schematics == | == Schematics == | ||
| − | We have an early Balthazar system scheme as a block diagram upon which we develop and prototype separate boards to | + | We have an early Balthazar system scheme as a block diagram upon which we develop and prototype separate boards to interchangeable compliance. |
| + | [[Image:BalthazarBlockDia122.svg]] | ||
| − | + | Balthazar laptop as a box consisting of mainboard + all the periphery needed that make up a | |
| − | Balthazar laptop as a box consisting of | + | complete laptop: display, audio, keyboard, mousepad, wireless, USB, HDMI... and additionally: a |
| − | complete laptop: display, audio, keyboard, mousepad, wireless, | ||
buffered GPIO (general purpose in/out) connector (not that laptop usually needs it...). | buffered GPIO (general purpose in/out) connector (not that laptop usually needs it...). | ||
The technology used benefits from the current rapid mobile platform development – as do all open- | The technology used benefits from the current rapid mobile platform development – as do all open- | ||
| − | source single-board computers:Banana Pi, Orange Pi 4 – and a bit more advanced Firefly- | + | source single-board computers: Banana Pi, Orange Pi 4 – and a bit more advanced Firefly- |
RK3399. They all use SOC (system on chip) as the miniaturized combination of CPU/GPU etc. The | RK3399. They all use SOC (system on chip) as the miniaturized combination of CPU/GPU etc. The | ||
| − | laptop should however be a pushed-up version of these single board computers - but still a single | + | the laptop should however be a pushed-up version of these single board computers - but still a single |
board computer. | board computer. | ||
One format of recent computers is also the mini-pc. They are usually based on Intel or AMD laptop | One format of recent computers is also the mini-pc. They are usually based on Intel or AMD laptop | ||
| − | computer processors. LattePanda seems to be on the side of single-board | + | computer processors. LattePanda seems to be on the side of single-board computers but uses Intel |
processors. Prices are also pushed up. | processors. Prices are also pushed up. | ||
| − | The interchangeable module should | + | The interchangeable module should be the board itself, while the stable part should be the |
| − | skeleton: a specifically designed housing with display, keyboard, audio, | + | skeleton: a specifically designed housing with display, keyboard, audio, touch-pad, power supply. |
To upgrade – one buys a new board and inserts it in the place of the old board. | To upgrade – one buys a new board and inserts it in the place of the old board. | ||
| + | |||
| + | If the keyboard PCB is meant to act as the complete top cover then its height is also defined by the LCD -> 180mm. The touch-pad module would fit above the keys (as was envisioned in the broad design considerations recently) – not as usual below the keys. | ||
| + | |||
| + | The two loudspeakers go to the usual positions left and right – at the two top edges of the full-size keyboard PCB. In this way, the acoustic horn effect will be at its best with the LCD screen up. | ||
| + | |||
| + | Ideas and some crude sketching of I/O boards and inner guts: | ||
| + | |||
| + | [[File:Innerguts drawing.png|thumb|center]] | ||
| + | |||
| + | The mechanical skeleton built in this manner needs additionally a USB hub board on the top right which also takes in all the necessary inner periphery (camera, keyboard). There are some of these hubs on the market but could be made here additionally. On to four hubs is perfectly ok - two externally accessed USB-connectors and two internally used for camera, keyboard. | ||
| + | |||
| + | The keyboard in this rudimentary fashion acting as the top is also very thin – maybe defining the triangle-like side cross-section – since there must be enough space at the top/ back/ bottom of the lower segment. The battery pack is consisting of LiIo batteries standardized in diameter – so this defines the height. About the same size are the vertically positioned USB-A female plugs. | ||
| + | The loudspeaker sound greatly benefits from this volume. | ||
| + | |||
| + | Let's repeat: the interchangeable CPU/ GPU upgrade module would be the mini-computer mainboard itself. To upgrade – one buys a new board and inserts it in the place of the old board or adds something else. | ||
| + | If the software and file system could be kept on some SSD version of mass storage – this would be an advantage (or maybe a necessity...). | ||
| + | |||
| + | |||
| + | Go to the: | ||
| + | [[Power_Supply| Power Supply]], [[I/O_USB|I/O hub]] or a [[Keyboard|Keyboard]] | ||
Latest revision as of 21:07, 10 October 2021
Schematics
We have an early Balthazar system scheme as a block diagram upon which we develop and prototype separate boards to interchangeable compliance.
Balthazar laptop as a box consisting of mainboard + all the periphery needed that make up a complete laptop: display, audio, keyboard, mousepad, wireless, USB, HDMI... and additionally: a buffered GPIO (general purpose in/out) connector (not that laptop usually needs it...). The technology used benefits from the current rapid mobile platform development – as do all open- source single-board computers: Banana Pi, Orange Pi 4 – and a bit more advanced Firefly- RK3399. They all use SOC (system on chip) as the miniaturized combination of CPU/GPU etc. The the laptop should however be a pushed-up version of these single board computers - but still a single board computer. One format of recent computers is also the mini-pc. They are usually based on Intel or AMD laptop computer processors. LattePanda seems to be on the side of single-board computers but uses Intel processors. Prices are also pushed up. The interchangeable module should be the board itself, while the stable part should be the skeleton: a specifically designed housing with display, keyboard, audio, touch-pad, power supply. To upgrade – one buys a new board and inserts it in the place of the old board.
If the keyboard PCB is meant to act as the complete top cover then its height is also defined by the LCD -> 180mm. The touch-pad module would fit above the keys (as was envisioned in the broad design considerations recently) – not as usual below the keys.
The two loudspeakers go to the usual positions left and right – at the two top edges of the full-size keyboard PCB. In this way, the acoustic horn effect will be at its best with the LCD screen up.
Ideas and some crude sketching of I/O boards and inner guts:
The mechanical skeleton built in this manner needs additionally a USB hub board on the top right which also takes in all the necessary inner periphery (camera, keyboard). There are some of these hubs on the market but could be made here additionally. On to four hubs is perfectly ok - two externally accessed USB-connectors and two internally used for camera, keyboard.
The keyboard in this rudimentary fashion acting as the top is also very thin – maybe defining the triangle-like side cross-section – since there must be enough space at the top/ back/ bottom of the lower segment. The battery pack is consisting of LiIo batteries standardized in diameter – so this defines the height. About the same size are the vertically positioned USB-A female plugs. The loudspeaker sound greatly benefits from this volume.
Let's repeat: the interchangeable CPU/ GPU upgrade module would be the mini-computer mainboard itself. To upgrade – one buys a new board and inserts it in the place of the old board or adds something else. If the software and file system could be kept on some SSD version of mass storage – this would be an advantage (or maybe a necessity...).
Go to the:
Power Supply, I/O hub or a Keyboard
